PENERAPAN MEDIA PEMBELAJARAN BERBANTUAN KOMPUTER UNTUK MENINGKATKAN HASIL BELAJAR SISWA PADA MATA PELAJARAN PNEUMATIK DAN HIDROLIK DI SMK AL – FALAH BANDUNG

Herlina, Lina (2017) PENERAPAN MEDIA PEMBELAJARAN BERBANTUAN KOMPUTER UNTUK MENINGKATKAN HASIL BELAJAR SISWA PADA MATA PELAJARAN PNEUMATIK DAN HIDROLIK DI SMK AL – FALAH BANDUNG. S1 thesis, Universitas Pendidikan Indonesia.

[img]
Preview
Text
S_TM_1005167_Title.pdf

Download (201kB) | Preview
[img]
Preview
Text
S_TM_1005167_Abstract.pdf

Download (152kB) | Preview
[img]
Preview
Text
S_TM_1005167_Table_of_content.pdf

Download (233kB) | Preview
[img]
Preview
Text
S_TM_1005167_Chapter1.pdf

Download (294kB) | Preview
[img] Text
S_TM_1005167_Chapter2.pdf
Restricted to Staf Perpustakaan

Download (619kB)
[img]
Preview
Text
S_TM_1005167_Chapter3.pdf

Download (470kB) | Preview
[img] Text
S_TM_1005167_Chapter4.pdf
Restricted to Staf Perpustakaan

Download (377kB)
[img]
Preview
Text
S_TM_1005167_Chapter5.pdf

Download (150kB) | Preview
[img]
Preview
Text
S_TM_1005167_Bibliography.pdf

Download (150kB) | Preview
[img] Text
S_TM_1005167_Appendix1.pdf
Restricted to Staf Perpustakaan

Download (235kB)
[img] Text
S_TM_1005167_Appendix2.pdf
Restricted to Staf Perpustakaan

Download (429kB)
Official URL: http://repository.upi.edu

Abstract

Kurangnya penggunaan media pembelajaran pada mata pelajaran pneumatik dan hidrolik menyebabkan proses pembelajaran menjadi kurang menarik, siswa menjadi kurang aktif, kurang memahami konsep dan cara kerja sistem pneumatik. Pada mata pelajaran ini dipelajari simbol dan cara kerja katup pneumatik yang sangat kompleks, sulit dipahami dan membutuhkan pemahaman yang tinggi, sehingga media pembelajaran sangat penting. Penelitian ini bertujuan untuk mengetahui peningkatan hasil belajar siswa dengan menggunakan modul cetak, peningkatan hasil belajar siswa dengan menggunakan media berbantuan komputer, perbedaan peningkatan hasil belajar antara siswa yang menggunakan modul cetak dan media berbantuan komputer. Metode yang digunakan pada penelitian ini adalah metode quasi eksperimental dengan non-equivalent control group design. Hasil pre-test dan post-test pada penelitian ini digunakan untuk mengetahui peningkatan hasil belajar siswa. Berdasarkan penelitian yang telah dilakukan, media pembelajaran yang digunakan dapat meningkatkan hasil belajar siswa dengan rata-rata N-Gain sebesar 0.21 termasuk kriteria rendah untuk modul cetak dan rata-rata N-Gain sebesar 0.32 termasuk kriteria sedang untuk media berbatuan komputer. Artinya terdapat perbedaan peningkatan hasil belajar antara siswa yang menggunakan modul cetak dan media berbantuan komputer. ----------- The lack of learning media use on pneumatic and hydraulic subjects causing the learning process becomes less interesting. On these subjects were studied the symbol and the workings of the pneumatic valves are very complex. It difficult to understand and requires an understanding of the high, learning media is very important. This research aims to know the improvement of student learning outcomes by using the print module, which are improved student learning outcomes with the use of computer-aided media and improved learning results. The method used in this research was quasi experimental methods with non-equivalent control group design. The results of pre-and post-test on this research is used to increase student learning outcomes. Based on the research that has done, learning media shows enhance the learning outcomes of students with average N-Gain of 0.21 including low criteria for the print module and an average N-Gain of 0.32 including criteria are for media computers. This means, there is a difference between learning outcomes increase in students using the print module and computer-aided media.

Item Type: Thesis (S1)
Additional Information: No. Panggil: S TM HER p-2017; Pembimbing: I. Dedi Rohendi, II. Purnawan; NIM: 1005167
Uncontrolled Keywords: katup pneumatik, modul cetak, media berbantuan komputer, peningkatan hasil belajar, Pneumatic valve, the print module, media, an increase in computer-aided learning results.
Subjects: L Education > LB Theory and practice of education > LB1603 Secondary Education. High schools
Q Science > QA Mathematics > QA75 Electronic computers. Computer science
T Technology > TA Engineering (General). Civil engineering (General)
Divisions: Fakultas Pendidikan Teknologi dan Kejuruan > Jurusan Pendidikan Teknik Mesin > Program Studi Pendidikan Teknik Mesin
Depositing User: Mr. Arif Rezkyana Nugraha
Date Deposited: 07 Aug 2018 08:49
Last Modified: 07 Aug 2018 08:49
URI: http://repository.upi.edu/id/eprint/30466

Actions (login required)

View Item View Item